Edit Info Other
Login

NVIDIA"

Differences between revisions 86 and 118 (spanning 32 versions)
⇤ ← Revision 86 as of 2017-06-09 09:26:03 →
Size: 7943
Editor: NicolasChauvet
Comment:
← Revision 118 as of 2019-07-09 09:50:48 → ⇥
Size: 11285
Editor: NicolasChauvet
Comment:
Deletions are marked like this. Additions are marked like this.
Line 11: Line 11:
nVidia has several driver series, each of which has different hardware support. To determine which driver you need to install, you'll first need to find your graphics card model. NVIDIA has several driver series, each of which has different hardware support. To determine which driver you need to install, you'll first need to find your graphics card model.
Line 33: Line 33:
This driver is suitable for any GPU found in 2010 and later.
{{{
dnf install xorg-x11-drv-nvidia akmod-nvidia "kernel-devel-uname-r == $(uname -r)"		 This driver is suitable for any GPU found in 2012 and later.
{{{
sudo dnf install xorg-x11-drv-nvidia akmod-nvidia
sudo dnf install xorg-x11-drv-nvidia-cuda #optional for cuda/nvdec/nvenc support
sudo dnf update -y
}}}
/!\ Please remember to wait after the RPM transaction ends, until the kmod get built. This can take up to 5 minutes on some systems.

=== Legacy GeForce 400/500 ===
Supported on current stable Xorg server release.

This driver is suitable for any NVIDIA Fermi GPU found between 2010 and 2012
{{{
sudo dnf install xorg-x11-drv-nvidia-390xx akmod-nvidia-390xx
sudo dnf install xorg-x11-drv-nvidia-390xx-cuda #optional for cuda up to 9.2 support
Line 38: Line 50:
Please remember to wait until the kmod get built earch time a new kernel rise up. This can take up to 5 minutes on some systems.


=== Legacy GeForce 8/9/200 ===		 /!\ Please remember to wait after the RPM transaction ends, until the kmod get built. This can take up to 5 minutes on some systems.

=== Legacy GeForce 8/9/200/300 ===
Line 44: Line 55:
dnf install xorg-x11-drv-nvidia-340xx akmod-nvidia-340xx "kernel-devel-uname-r == $(uname -r)"
dnf update -y
}}}
Please remember to wait until the kmod get built earch time a new kernel rise up. This can take up to 5 minutes on some systems.		 sudo dnf install xorg-x11-drv-nvidia-340xx akmod-nvidia-340xx
sudo dnf install xorg-x11-drv-nvidia-340xx-cuda #optional for cuda up to 6.5 support
sudo dnf update -y
}}}
/!\ Please remember to wait until the kmod get built earch time a new kernel rise up. This can take up to 5 minutes on some systems.
Line 50: Line 62:
Supported on current stable Xorg server release.
{{{
dnf install xorg-x11-drv-nvidia-304xx akmod-nvidia-304xx "kernel-devel-uname-r == $(uname -r)"
dnf update -y
}}}
Please remember to wait until the kmod get built earch time a new kernel rise up. This can take up to 5 minutes on some systems.		 Supported up to Fedora 27 - EOL, no more nvidia updates
Line 59: Line 66:
{{{
yum install akmod-nvidia-173xx "kernel-devel-uname-r == $(uname -r)"
yum update -y
}}}
Line 65: Line 69:
{{{
yum install akmod-nvidia-96xx "kernel-devel-uname-r == $(uname -r)"
yum update -y
}}}
Line 73: Line 74:
With Fedora 25 and later, Optimus devices are supported automatically by default. Please see the dedicated [[Howto/Optimus]].
With Fedora 25 and later, Optimus devices are supported automatically by default. Please see the dedicated [[Howto/Optimus|Optimus Howto]].


=== Silverblue ===
Silverblue is supported with the NVIDIA driver using akmod-nvidia starting with f30. (only the current NVIDIA driver is tested). Please follow the [[Configuration|Configuration]] page first.
{{{
sudo rpm-ostree install akmod-nvidia xorg-x11-drv-nvidia
sudo rpm-ostree install akmod-nvidia xorg-x11-drv-nvidia-cuda #optional if using nvidia-smi or cuda
sudo rpm-ostree kargs --append=rd.driver.blacklist=nouveau --append=modprobe.blacklist=nouveau --append=nvidia-drm.modeset=1 # this might not be needed at some point when silverblue will support the standard way to specify this.
}}}


=== Switching between nouveau/nvidia ===
With recent drivers as packaged with RPM Fusion, it is possible to switch easily between nouveau and nvidia while keeping the nvidia driver installed.
When you are about to select the kernel at the grub menu step. You can edit the kernel entry, find the linux boot command line and manually remove the following options "rd.driver.blacklist=nouveau modprobe.blacklist=nouveau nvidia-drm.modeset=1".
This will allow you to boot using the nouveau driver instead of the nvidia binary driver.
At this time, there is no way to make the switch at runtime.
Line 80: Line 96:
dnf install xorg-x11-drv-nvidia-cuda
}}}


=== VULKAN ===
The main package support vulkan, but you need to install the vulkan libraries if requested.
{{{
dnf install vulkan
}}}
 sudo dnf install xorg-x11-drv-nvidia-cuda
}}}


=== KMS ===
KMS stands for "Kernel Mode Setting" which is the opposite of "Userland Mode Setting". This feature allows to set the screen resolution on the kernel side once (at boot), instead of after login from the display manager.
This feature has early support in the main NVIDIA driver, but is not enabled by default yet as it may crash. To enable, use:
{{{
sudo grubby --update-kernel=ALL --args='nvidia-drm.modeset=1'
}}}
Please have a look at the Wayland section if using it (specially for gnome users).


=== Vulkan ===
The main package support Vulkan, but you need to install the vulkan libraries if requested.
{{{
sudo dnf install vulkan
}}}

=== Wayland ===
Gnome with Wayland and NVIDIA doesn't work by default at this point.

With Fedora 29, mutter has support for NVIDIA eglstream but it's disabled at runtime by a udev rules. You need to comment the "DRIVER==nvidia" line in /usr/lib/udev/rules.d/64-gdm.rules. You will also have to comment "WaylandEnable=false" in /etc/gdm/custom.conf


=== NVENC/NVDEC ===
RPM Fusion support ffmpeg compiled with NVENC/NVDEC with Fedora 25 and later. You need to have a recent NVIDIA card (see the [[https://developer.nvidia.com/ffmpeg|support matrix]]), and install the cuda sub-package.
{{{
sudo dnf install xorg-x11-drv-nvidia-cuda-libs
}}}

Please have a look on the ffmpeg [[https://trac.ffmpeg.org/wiki/HWAccelIntro#NVENC|HWAccel introduction]] to the feature
Line 94: Line 132:
dnf install "kernel-devel == $(uname -r)"
dnf update -y
dnf --enablerepo=rpmfusion-nonfree-rawhide install akmod-nvidia 		sudo dnf install "kernel-devel == $(uname -r)"
sudo dnf update -y
sudo dnf --enablerepo=rpmfusion-nonfree-rawhide install akmod-nvidia xorg-x11-drv-nvidia --nogpgcheck
Line 101: Line 139:
dnf install "kernel-devel-uname-r == $(uname -r)"
dnf update -y
dnf --releasever=25 install akmod-nvidia xorg-x11-drv-nvidia		 sudo dnf install "kernel-devel-uname-r == $(uname -r)"
sudo dnf update -y
sudo dnf --releasever=30 install akmod-nvidia xorg-x11-drv-nvidia --nogpgcheck
}}}

=== nvidia-xconfig ===
This tool is only meant to be used as a sample to create a xorg.conf files. But don't use this directly as the generated xorg.conf is known to broke with many default Fedora/RHEL Xorg server options.
Instead, you should probably start with :
{{{
sudo cp /usr/share/X11/xorg.conf.d/nvidia.conf /etc/X11/xorg.conf.d/nvidia.conf
Line 113: Line 158:
In order to enable video acceleration support for your player and if your nvidia card is recent enough (Geforce 8 and later is needed). You can install theses packages:
{{{
# dnf install vdpauinfo libva-vdpau-driver libva-utils
}}}

With the native vdpau backend from a nvidia card, the output is similar to this:		 In order to enable video acceleration support for your player and if your NVIDIA card is recent enough (Geforce 8 and later is needed). You can install theses packages:
{{{
# sudo dnf install vdpauinfo libva-vdpau-driver libva-utils
}}}

With the native vdpau backend from a NVIDIA card, the output is similar to this:
Line 153: Line 198:
Secure Boot currently blocks the kernel from loading the nvidia driver. It must be disabled before booting the OS. Secure Boot currently blocks the kernel from loading the NVIDIA driver. It must be disabled before booting the OS.
Line 156: Line 201:
Rawhide kernels are built with debug enabled GPL-only symbols which kernel is incompatible with the nvidia binary-only driver. Rawhide kernels are built with debug enabled GPL-only symbols which kernel is incompatible with the NVIDIA binary-only driver.
Line 159: Line 204:
dnf config-manager --add-repo=http://dl.fedoraproject.org/pub/alt/rawhide-kernel-nodebug/fedora-rawhide-kernel-nodebug.repo
dnf update		 sudo dnf config-manager --add-repo=http://dl.fedoraproject.org/pub/alt/rawhide-kernel-nodebug/fedora-rawhide-kernel-nodebug.repo
sudo dnf update
Line 165: Line 210:
dnf downgrade xorg-x11-server\* --releasever=22 --allowerasing
echo "exclude=xorg-x11*" >> /etc/dnf/dnf.conf
}}}


== Uninstall the nvidia driver ==		 sudo dnf downgrade xorg-x11-server\* --releasever=29 --allowerasing
sudo echo "exclude=xorg-x11*" >> /etc/dnf/dnf.conf
}}}


== Uninstall the NVIDIA driver ==
Line 177: Line 222:
== Recover from nvidia installer ==
The nvidia binary driver installer overwrite some configuration and libraries. If you want to recover to a clean state, either to use nouveau or the packaged driver, use:		 == Recover from NVIDIA installer ==
The NVIDIA binary driver installer overwrite some configuration and libraries. If you want to recover to a clean state, either to use nouveau or the packaged driver, use:
Line 182: Line 227:
dnf re-install xorg-x11-server-Xorg mesa-libGL mesa-libEGL dnf reinstall xorg-x11-server-Xorg mesa-libGL mesa-libEGL libglvnd\*
Line 188: Line 233:
If you still cannot make the driver to work, you can either report a problem to nVidia or to RPM Fusion packager team. If you still cannot make the driver to work, you can either report a problem to NVIDIA or to RPM Fusion packager team.
Line 190: Line 235:

Basically, you need to generate an archive and attach it to bugzilla or any paste service.
{{{
sudo nvidia-bug-report.sh
zcat nvidia-bug-report.log.gz | fpaste
}}}

Contents

  1. About this Howto
  2. Determining your card model
  3. Installing the drivers
    1. Current GeForce/Quadro/Tesla
    2. Legacy GeForce 400/500
    3. Legacy GeForce 8/9/200/300
    4. Legacy GeForce 6/7
    5. Legacy GeForce 5 (FX series)
    6. Legacy GeForce 2 through GeForce 4
  4. Special notes
    1. Optimus
    2. Silverblue
    3. Switching between nouveau/nvidia
    4. CUDA
    5. KMS
    6. Vulkan
    7. Wayland
    8. NVENC/NVDEC
    9. Latest/Beta driver
    10. nvidia-xconfig
    11. x86_64 (64bit) users
    12. PAE (Physical Address Extension) kernel users
    13. VDPAU/VAAPI
    14. Akmods
    15. Nouveau compatibility
    16. Secure Boot
    17. Rawhide
  5. Uninstall the NVIDIA driver
  6. Recover from NVIDIA installer
  7. Bug Report

About this Howto

This howto will help you install the correct NVIDIA driver on Fedora for your graphics card as well as troubleshoot common driver problems.

The prerequisite is to have followed the Configuration page to have at least the RPM Fusion nonfree section available.

Determining your card model

NVIDIA has several driver series, each of which has different hardware support. To determine which driver you need to install, you'll first need to find your graphics card model.

If you don't know it, open a Terminal (Applications > System Tools > Terminal) and type: 

/sbin/lspci | grep -e VGA

You can also check the supported chips section and see which series is recommended for you card, then install the appropriate driver series. Please remember that you need additional steps for optimus.

You are probably in the Optimus case if your NVIDIA card is found with the next command: 

/sbin/lspci | grep -e 3D

Installing the drivers

Please remember that once the driver is installed, there is no need to configure xorg.conf by default unless you are using an Optimus device. Changes will take effect after a full reboot on the newest kernel.

Current GeForce/Quadro/Tesla

Supported on current stable Xorg server release.

This driver is suitable for any GPU found in 2012 and later. 

sudo dnf install xorg-x11-drv-nvidia akmod-nvidia
sudo dnf install xorg-x11-drv-nvidia-cuda #optional for cuda/nvdec/nvenc support
sudo dnf update -y

/!\ Please remember to wait after the RPM transaction ends, until the kmod get built. This can take up to 5 minutes on some systems.

Legacy GeForce 400/500

Supported on current stable Xorg server release.

This driver is suitable for any NVIDIA Fermi GPU found between 2010 and 2012 

sudo dnf install xorg-x11-drv-nvidia-390xx akmod-nvidia-390xx
sudo dnf install xorg-x11-drv-nvidia-390xx-cuda #optional for cuda up to 9.2 support
dnf update -y

/!\ Please remember to wait after the RPM transaction ends, until the kmod get built. This can take up to 5 minutes on some systems.

Legacy GeForce 8/9/200/300

Supported on current stable Xorg server release. 

sudo dnf install xorg-x11-drv-nvidia-340xx akmod-nvidia-340xx
sudo dnf install xorg-x11-drv-nvidia-340xx-cuda #optional for cuda up to 6.5 support
sudo dnf update -y

/!\ Please remember to wait until the kmod get built earch time a new kernel rise up. This can take up to 5 minutes on some systems.

Legacy GeForce 6/7

Supported up to Fedora 27 - EOL, no more nvidia updates

Legacy GeForce 5 (FX series)

Supported up to Fedora 20 - EOL, no more nvidia updates

Legacy GeForce 2 through GeForce 4

Supported up to Fedora 14 - EOL, no more nvidia updates

Special notes

Optimus

With Fedora 25 and later, Optimus devices are supported automatically by default. Please see the dedicated Optimus Howto.

Silverblue

Silverblue is supported with the NVIDIA driver using akmod-nvidia starting with f30. (only the current NVIDIA driver is tested). Please follow the Configuration page first. 

sudo rpm-ostree install akmod-nvidia xorg-x11-drv-nvidia
sudo rpm-ostree install akmod-nvidia xorg-x11-drv-nvidia-cuda #optional if using nvidia-smi or cuda
sudo rpm-ostree kargs --append=rd.driver.blacklist=nouveau --append=modprobe.blacklist=nouveau --append=nvidia-drm.modeset=1 # this might not be needed at some point when silverblue will support the standard way to specify this.

Switching between nouveau/nvidia

With recent drivers as packaged with RPM Fusion, it is possible to switch easily between nouveau and nvidia while keeping the nvidia driver installed. When you are about to select the kernel at the grub menu step. You can edit the kernel entry, find the linux boot command line and manually remove the following options "rd.driver.blacklist=nouveau modprobe.blacklist=nouveau nvidia-drm.modeset=1". This will allow you to boot using the nouveau driver instead of the nvidia binary driver. At this time, there is no way to make the switch at runtime.

CUDA

The driver support CUDA when installing the xorg-x11-drv-nvidia-cuda subpackage. Please have a look on the dedicated CUDA Howto 

sudo dnf install xorg-x11-drv-nvidia-cuda

KMS

KMS stands for "Kernel Mode Setting" which is the opposite of "Userland Mode Setting". This feature allows to set the screen resolution on the kernel side once (at boot), instead of after login from the display manager. This feature has early support in the main NVIDIA driver, but is not enabled by default yet as it may crash. To enable, use: 

sudo grubby --update-kernel=ALL --args='nvidia-drm.modeset=1'

Please have a look at the Wayland section if using it (specially for gnome users).

Vulkan

The main package support Vulkan, but you need to install the vulkan libraries if requested. 

sudo dnf install vulkan

Wayland

Gnome with Wayland and NVIDIA doesn't work by default at this point.

With Fedora 29, mutter has support for NVIDIA eglstream but it's disabled at runtime by a udev rules. You need to comment the "DRIVER==nvidia" line in /usr/lib/udev/rules.d/64-gdm.rules. You will also have to comment "WaylandEnable=false" in /etc/gdm/custom.conf

NVENC/NVDEC

RPM Fusion support ffmpeg compiled with NVENC/NVDEC with Fedora 25 and later. You need to have a recent NVIDIA card (see the support matrix), and install the cuda sub-package. 

sudo dnf install xorg-x11-drv-nvidia-cuda-libs

Please have a look on the ffmpeg HWAccel introduction to the feature

Latest/Beta driver

You can install the latest drivers from Rawhide using the following command: 

sudo dnf install "kernel-devel == $(uname -r)"
sudo dnf update -y
sudo dnf --enablerepo=rpmfusion-nonfree-rawhide install akmod-nvidia xorg-x11-drv-nvidia --nogpgcheck

Or if you want to grab it from the latest fedora stable release: 

sudo dnf install "kernel-devel-uname-r == $(uname -r)"
sudo dnf update -y
sudo dnf --releasever=30 install akmod-nvidia xorg-x11-drv-nvidia --nogpgcheck

nvidia-xconfig

This tool is only meant to be used as a sample to create a xorg.conf files. But don't use this directly as the generated xorg.conf is known to broke with many default Fedora/RHEL Xorg server options. Instead, you should probably start with : 

sudo cp /usr/share/X11/xorg.conf.d/nvidia.conf /etc/X11/xorg.conf.d/nvidia.conf

x86_64 (64bit) users

If you wish to have 3D acceleration in 32bit packages such as Wine, be sure to install the appropriate 32bit version of the xorg-x11-drv-nvidia-libs package for your driver variant. For example, if you installed kmod-nvidia then you will require xorg-x11-drv-nvidia-libs.i686. With Current Fedora (not EL), this is handled automatically by RPM (Boolean dependencies).

PAE (Physical Address Extension) kernel users

If you are on a 32bit (i686) system and have the kernel-PAE installed to access more RAM, please install kernel-PAE-devel. Please note that this step is not required for any 64bit (x64_64) users.

VDPAU/VAAPI

In order to enable video acceleration support for your player and if your NVIDIA card is recent enough (Geforce 8 and later is needed). You can install theses packages: 

# sudo dnf install vdpauinfo libva-vdpau-driver libva-utils

With the native vdpau backend from a NVIDIA card, the output is similar to this: 

$ vdpauinfo 
display: :0.0   screen: 0
API version: 1
Information string: NVIDIA VDPAU Driver Shared Library  375.66  Mon May  1 14:32:38 PDT 2017
...

Here is an example of an accurate output of vainfo, when the bridge to the VAAPI is correctly installed. 

$ vainfo 
libva info: VA-API version 0.40.0
libva info: va_getDriverName() returns 0
libva info: Trying to open /usr/lib64/dri/nvidia_drv_video.so
libva info: Found init function __vaDriverInit_0_40
libva info: va_openDriver() returns 0
vainfo: VA-API version: 0.40 (libva )
vainfo: Driver version: Splitted-Desktop Systems VDPAU backend for VA-API - 0.7.4
vainfo: Supported profile and entrypoints
...

Akmods

An akmod is a type of package similar to dkms. As you start your computer, the akmod system will check if there are any missing kmods and if so, rebuild a new kmod for you. Akmods have more overhead than regular kmod packages as they require a few development tools such as gcc and automake in order to be able to build new kmods locally.

Nouveau compatibility

As nouveau is enabled by default starting with Fedora 11, you may experience problem which is caused by the nouveau kernel module being present in the initrd image. Once the driver is installed and after the reboot, this command should not output anything: 

lsmod |grep nouveau

Secure Boot

Secure Boot currently blocks the kernel from loading the NVIDIA driver. It must be disabled before booting the OS.

Rawhide

Rawhide kernels are built with debug enabled GPL-only symbols which kernel is incompatible with the NVIDIA binary-only driver. You need to use the Rawhide nodebug repository. 

sudo dnf config-manager --add-repo=http://dl.fedoraproject.org/pub/alt/rawhide-kernel-nodebug/fedora-rawhide-kernel-nodebug.repo
sudo dnf update

Please remind that Xorg server version is also to take into consideration. In the case of incompatibilities with the xorg-server, you might need to downgrade to the previous fedora release: 

sudo dnf downgrade xorg-x11-server\* --releasever=29 --allowerasing
sudo echo "exclude=xorg-x11*" >> /etc/dnf/dnf.conf

Uninstall the NVIDIA driver

dnf remove xorg-x11-drv-nvidia\*

Recover from NVIDIA installer

The NVIDIA binary driver installer overwrite some configuration and libraries. If you want to recover to a clean state, either to use nouveau or the packaged driver, use: 

rm -f /usr/lib{,64}/libGL.so.* /usr/lib{,64}/libEGL.so.*
rm -f /usr/lib{,64}/xorg/modules/extensions/libglx.so
dnf reinstall xorg-x11-server-Xorg mesa-libGL mesa-libEGL libglvnd\*
mv /etc/X11/xorg.conf /etc/X11/xorg.conf.saved

Bug Report

If you still cannot make the driver to work, you can either report a problem to NVIDIA or to RPM Fusion packager team. Please read: If you have a problem, PLEASE read this first

Basically, you need to generate an archive and attach it to bugzilla or any paste service. 

sudo nvidia-bug-report.sh
zcat nvidia-bug-report.log.gz | fpaste

CategoryHowto

Howto/NVIDIA (last edited 2024-08-30 16:31:12 by NicolasChauvet)